View source

===Pick a firmware===

* vehicle/openwrt/kamikaze_8.09/openwrt-brcm47xx-squashfs.trx - linux 2.6, open source wifi driver
* vehicle/openwrt/kamikaze_8.09/openwrt-brcm-2.4-squashfs.trx - linux 2.4, proprietary wifi driver

===Install using TFTP===

To install OpenWrt using TFTP or the ASUS firmware restoration tool you have to put the router in diag mode. To put the router in the diag mode, do this:

* Unplug the router's power cord.
* Confirm your PC is configured to an address like 192.168.1.100
* Connect the router's LAN1 port directly to your PC.
* Push the black RESTORE button using a pen or such, and keep the button pushed down.
* Plug the power on while keeping the RESTORE button pushed for few seconds.
* When you see a slowly blinking power light, you are in diag mode.
* Now the router should accept an image via TFTP or via the ASUS firmware restoration tool. 

Make sure you have atftp installed.

In diag mode, the router takes address 192.168.1.1. It responds to ping, so you can confirm that it is in diag mode and ready for the tftp by using "ping 192.168.1.1".

* Execute the TFTP commands below:
 atftp 192.168.1.1
 tftp> mode octet
 tftp> trace
 tftp> put openwrt-brcm47xx-squashfs.trx

* After the TFTP upload is complete, wait at least six minutes. The firmware is first loaded into the RAM, and then flashed. This process takes a little time, and to ensure that the router is not bricked you should wait six minutes.
* The router will reboot itself automatically after the upgrade is complete. Rebooting may take a while. It might be the case that the router does not reboot by itself; if this happens it should be safe to wait for the period mentioned and then to do a manual reboot (pull the power-cord).
* You are done! You should be able to telnet to your router (IP address: 192.168.1.1) and start configuring. First set a password for root so you can use ssh instead of telnet from now on.

 telnet 192.168.1.1

 passwd 

NOTES:

* Netkit's tftp doesn't work quite often; use atftp.
* After TFTP upload is complete, DON'T reboot (replug) too early! It might brick your router.
* The ASUS WL-500g Premium does not revert to the 192.168.1.1 address when starting the CFE bootloader, but uses the LAN IP address set in NVRAM. Try this address if you have difficulties. 

=== Initial Configuration ===

 opkg update
 opkg install kmod-usb-ehci kmod-usb-uhci kmod-usb-storage kmod-usb2 \
  kmod-usb-serial-ftdi kmod-usb-serial-pl2303 kmod-fs-ext2 kmod-fs-ext3 \
  rsync e2fsprogs curl usbutils \
  perl perlbase-essential perlbase-config perlbase-getopt perlbase-data \
  perlbase-bytes perl-uri perlbase-scalar perlbase-list \
  gphoto2

IP: 10.11.12.1 

Add autoinet.sh

Prepare USB flash drive with ext3

Make chroot


=== Misc notes ===
wlan0 - wifi
eth0.1 - wan
br-lan - lan 4 port switch
eth0 - ?
eth1 - ?
eth0.0 - ?
wmaster0 - ?

ifconfig wlan0 up

dhcp klient na wan
dhcp server na lan

nastavit lan ip stevilke
br-lan 10.11.12.1
dhcp 10.11.12.100-199

dodat backports ipkg source - kje je za naso verzijo kamikaze?
ne instalirat gpsd

iwconfig wlan0 power on    
iwlist wlan0 scanning

ntpclient -h time.arnes.si

#manual connect:
iwconfig wlan0 mode managed
iwconfig wlan0 essid PIKSEL
udhcpc -qn -i wlan0

chroot /mnt/usbdrive
swapon /swap/16Mb
mount -t proc none /proc
mount -t devfs devfs /dev

#clock
/usr/sbin/ntpclient -l -h fr.pool.ntp.org -c 1 -s

#arduino serial port device
mknod /dev/arduino c 4 65


=== openvpn ===

On laptop:

 cd wlan
 scp -r * root@router:/etc/
 # register IP on http://wlan-lj.net
 # fix IP address in /etc/openvpn/wlanlj.conf

On router:

 opkg install openvpn olsrd
 /etc/init.d/openvpn enable
 /etc/init.d/olsrd enable
 /etc/init.d/openvpn start
 /etc/init.d/olsrd start